Tuesday, October 5, 2010

Air Layering Bay Laurel Bonsai

Layering is a method for plant propagation somehow unusual for many gardeners,although it is a great way to multiply plants, especially for difficult-to-root plants. Air layering is easy, and the success rate is much higher then rooting cuttings.

Air Layering  Bay Laurel Bonsai

Few techniques are used in air layering (based on old Chinese methods):
- Ring Bark technique: scrape off the cambium layer back to wood on a bark portion with length more than 2x the branch diameter (for safety cut off only half ring).
- Tourniquet technique: select branch, loop a wire around and below the junction of a branch, twist tight until the wire cuts into the bark.
- Bridge technique: remove 3-5mm strips rather then full ring-bark all the way around the branch, leaving bark strips for nutrient flows.
- Skirt techniques: make one circular cut with few vertical slits, then peel upwards the bark. Twist a metal ring up under the slivers to stop them moving back and to force the new roots to jump into the moss.
After this, in all cases, is needed to dust the wounded area with rooting hormone powder, then place a ball of sphagnum moss with moist clay around the junction of branch. Around the stem, the rooting mix can be fixed by a sturdy flowerpot or a piece of plastic wrapped around scraped bark portion. The layered plant will start to form roots growing a callous-type of tissue in the rooting ball.


I have already told you two months ago about my attempt to propagate my own edible bonsai Laurus Nobilis, Bay Laurel (Dafin) using air layering.

Air layered Bay Laurel Trees


In April I layered a large branch of laurel tree (the best time to layer is in spring) and now I'm glad to tell you that I have another "baby" bay tree ... actually a clone.

Bay Laurel Tree with air layered branch

For this project I used skirt technique - and I selected a 6 -7 cm length section of stem without small branches around. With a sharp knife I cut almost all the way around the branch (except 5 mm leaved for plant safety to maintain the nutrients flow) and  I peel upward the bark. I twisted tight a metal wire under the slivers until finely cuts the bark on the portion of 5 mm uncut bark. I sprinkled a pinch of rooting hormone powder for hardwood then I made a rooting ball with peat moss and moisten clay and I wrapped a piece of polyethylene film around the stem to hold the rooting mix, securing the wrapper to the stem up and at the bottom with plastic ties. Once a week  I re-moisten this mix, inserting water in the plastic "bag" with a syringe dispenser.

Few weeks ago I saw that a good set of roots was forming and after the new roots have penetrated the moss ball we decided that is time to detach the new plant. Without disturbing the roots or removing the ball of moss,  last week we cut off  the rooted branch and planted it in a ceramic pot.

Bay Laurel rooted branchBay Laurel without air layered branch

For the next 2 weeks we will keep the plant under shade until the new root system  is well established and developed to sustain the new bay tree. Now my bay laurel bonsai (mother plant) looks somehow different without its rooted branch but I'm very happy about my gardening success and I hope that my new Bay Laurel tree will be happy to look after itself in next period.


Bay Laurel mother plant without air layered branch
Air layered branch separated from Bay Laurel mother plant

4 comments:

Xenia said...

Wow, that's amazing! I've definitely never done anything like this, I'm so impressed! Both of your plants look like they're healthy and thriving, you did a great job.

Thanh said...

That really is amazing! I'm still not sure I can do this myself. I think I will need a tutorial class or something. But your website has been very informative. This layering technique looks fascinating. Perhaps I will try this to see if I can do it too. Thank you for sharing your knowledge! I love your pictures too. Great job!

Anonymous said...

I've done this technique with sphagnum moss two weeks ago hope it works.. Do I need to water the moss? If so how often.. Thanks

Scented Leaf said...

Yes, you need to add water to keep the medium wet ... but don't forget to puncture the plastic wrap so the water can drain.
Good luck.

Tags

Relax (67) Vancouver (67) Scented Pelargonium (66) Flowers (47) Bonsai (44) Nature (41) Events (40) Decoration (34) Garden (34) Tree (26) Saikei (24) Herbs (22) Quotes (22) Indoor Plants (20) Wildlife (18) Poem (17) Seed (16) Recipes (15) Memories (14) Propagation (14) VanDusen (14) Accent Plants (13) Stanley Park (13) 3D Object Movie (10) Ficus (9) Abstract Art (8) Herbal Tea (8) Fireworks (6) Geranium (6) Bay Laurel (5) Indian Totem Poles (5) Pelargonium (5) Romania (5) UBC (5) Bulbs (3) Giveaway (3) Spruce (3) Ginkgo (2) Moringa (2) Pine (2) Erodium (1) Frankia (1) Juniper (1) Thuja (1) Truffle (1)
Scented Pelargoniums Seeds available for sale on our Store. Free Shipping !!!

Search our Blog